Service your mower between December and February, after the last cut and before the first one in March. A sharp blade cuts the grass cleanly; a blunt one tears it, leaving ragged brown tips that let disease in.
You can do a basic service yourself in an hour: clean the deck, sharpen the blade and, on a petrol mower, change the oil, plug and air filter. If you'd rather not, book it into a mower shop in winter. They're quiet then, and you won't be queuing with everyone else in spring.
Cylinder mowers are the exception: their blades need specialist sharpening, so send those to a shop.
When to service a mower
Do it once a year, in winter:
- Clean it after the last cut in October or November, before you put it away
- Service it from December to February, when you won't need it for weeks
- Check the blade again in summer if you've hit stones or the cut looks ragged
Petrol mowers need servicing before every season. Electric and cordless mowers need less, but their blades go blunt just as fast.
How to tell the blade is blunt
Look at the grass a day or two after mowing. If the tips have turned brown and, close up, they're jagged instead of cut straight, the blade needs sharpening.
Blunt blades tear the grass instead of slicing it, and blunt rotary mowers often fail to cut the grass at all. Torn grass is more open to disease, insect damage and drought. My guide on how to mow the lawn explains why a clean cut matters.
Safety first
Make sure the mower can't start before you touch the blade. Do this every time:
- Petrol mower: pull the lead off the spark plug
- Cordless mower: take the battery out
- Electric mower: unplug it at the socket
Wear thick gloves and eye protection. The blade is sharp even when it's blunt, and filing throws off metal splinters.
How to clean the mower
Grass that dries on the underside of the deck holds moisture against the metal and rusts it. It also blocks the airflow that lifts the grass into the box. Clean it like this:
- Empty the fuel tank on a petrol mower by running it dry, or follow the manual's advice on storing fuel over winter. Old petrol can stop it starting in spring.
- Tip the mower on its side the way the manual says, usually with the air filter and carburettor facing up, so oil and fuel don't leak into them.
- Scrape the dried grass off the underside with a plastic scraper or an old paint scraper.
- Brush off the rest and wipe the deck down. Don't hose a petrol or electric mower.
- Clean the grass box, the wheels and the cutting height levers, and check the box isn't torn.
How to sharpen a rotary mower blade
With the mower safe to work on, sharpen the blade in this order:
- Mark the blade with a marker pen so you put it back the right way up.
- Wedge the blade with a block of wood so it can't turn, then undo the bolt. It's often tight, so use a long spanner rather than a short one.
- Clamp the blade in a vice and look at the cutting edges. If it's bent, cracked or worn thin, replace it. A new blade for most mowers is cheap.
- File each cutting edge with a flat file, following the original angle. Push the file away from you along the edge; don't saw back and forth.
- File both ends the same number of strokes, so the blade stays balanced.
- Check the balance on a blade balancer, or hang it by the centre hole on a nail. If one end drops, file a little more off that end until it sits level.
- Refit the blade the right way up and tighten the bolt to the torque in the manual.
You can also sharpen a blade on a bench grinder, which is quicker, but go gently: too much heat softens the metal and it goes blunt again quickly.
An unbalanced blade makes the mower vibrate, which wears out the engine or motor bearings. If you're not sure, take it to a mower shop to sharpen and balance.
Petrol mower service
On a petrol mower, do these as well, with parts that match your model number:
- Change the oil. Run the engine for a few minutes so the oil flows, stop it and pull the plug lead, then drain the oil as the manual says. Refill to the mark on the dipstick, no higher.
- Replace the spark plug, or clean it with a wire brush if it's in good condition, and check the gap.
- Clean or replace the air filter. A paper filter is replaced; a foam one can be washed, dried and re-oiled.
- Check the cables for the throttle and the blade brake, and oil any pivot points.
Take the old oil to your local recycling centre. Don't pour it down a drain.
Electric and cordless mowers
These need less, but don't skip them:
- Check the cable on an electric mower for cuts and damage, and always plug it in through an RCD (a residual current device), which cuts the power if the cable is damaged
- Store cordless batteries indoors over winter, somewhere cool and dry, and charge them as the manual says
- Clean the motor vents so it doesn't overheat
- Test the safety handle: the blade should stop as soon as you let go
Cylinder mowers
A cylinder mower has a spinning cylinder of blades that cuts against a fixed bottom blade, like scissors. When it's sharp, it gives one of the cleanest cuts you can get.
Sharpening and setting a cylinder needs special tools, so send cylinder mowers to your local mower shop. Between services, you can adjust the gap between the cylinder and the bottom blade as the manual says: it should cut a strip of paper cleanly along its whole width.
Other tools to check
While you're at it, give your other lawn tools a once-over before spring:
- Strimmer: new line, clean the guard
- Edging iron and shears: sharpen and oil them; see how to edge a lawn
- Spreader: wash out old feed, which corrodes it
- Sprayer: rinse it through, and keep one only for weedkiller
- Rakes and forks: tighten loose heads, oil wooden handles
FAQs
How often should I sharpen my mower blade?
At least once a year, in winter. Check it again in mid-summer if your lawn is large, you mow weekly, or you've hit stones or roots. Brown, ragged grass tips a day or two after mowing are the sign it needs doing.
Is it worth getting a mower serviced?
For a petrol mower, yes, if you'd rather not do the oil, plug and filter yourself. Book it in between December and February, when mower shops are quiet. A cylinder mower should always go to a shop.
Can I sharpen a mower blade without taking it off?
You can touch up the edge with a file, but it's hard to file evenly and impossible to check the balance. Take the blade off, sharpen it in a vice and balance it before you refit it.
When should I replace a mower blade instead of sharpening it?
Replace it if it's bent, cracked, chipped deeply or worn thin from years of sharpening. A bent blade can't be balanced, and a cracked one can break up while it spins.
Read next: First mow of the season, for getting the lawn ready for its first cut in March.


